The Chevy engine oil pressure sensor difficulty has to be going on because that a lengthy time. With that said, the vehicles v the most pressure switch problems fall in the selection of V-8 engines indigenous 2003 with 2012. At some suggest in the model year that 2007, Chevrolet establish an worry existed.

You are watching: Where is the oil pressure sensor on a 4.3 vortec

They decided to ar a filter screen around the Chevrolet engine oil press sensor. They did this due to the fact that they thought sludge and debris found its method into the sensor. Not just did this not solve the problem, it produced another. Currently sometimes as soon as you pull the protective filter display out, you find it completely clogged.This method if you replace the oil pressure sensor, due to the fact that you think it"s bad and also you execute not replace the filter screen approximately it, the same difficulty reoccurs. Due to the fact that the component isn"t easy to replace you really want to acquire it best the very first time. Unfortunately, civilization usually read the very first paragraph of this articles and just change the very first part mentioned.

I"m asking you to hang in there with me and also read v this entire page. Not just will I provide tips to aid with the replacement of this unreliable Chevy engine oil push sensor, but we"ll talk about a many the problems linked with this repair and also the common computer and also sensor password set. Finally, we incorporate pictures of exactly where the part is located.

Symptoms the Oil pressure Problems

The very first time i ran throughout the Chevy engine oil pressure problem the customer complained around an oil gauge that review zero and also a check engine light. Obviously the motor was obtaining oil pressure, because there wasn"t any kind of noise.After connecting a scan device I uncovered a code P0521 and trouble password P0523. This codes stand for engine oil push sensor move performance the end of selection and sensor high-voltage. Note that it"s likewise common to uncover a P0520, standing because that oil push sensor circuit malfunction and P0522 circuit voltage low.Also precious mentioning, a warning blog post on the dash stated low oil, revolve engine off. This warning went unheeded by my customer, yet you should always follow the instructions simply in case. I have seen general Motors press gauges and also warning lights malfunctioning since I very first got in the company in 1984.

Standard diagnosis measures remain the same. The method to find out what"s wrong v the car is to remove the oil push sensor or switch and connect a mechanically gauge. This way you"re analysis the mechanically engine oil pump pressure and also not trusting the electronic devices that report this reading.Although ns still think in this method of diagnosis, most people don"t have actually a mechanical oil press gauge. However, if you have a Chevy V-8 engine in between the design years of 2003 through 2012 it"s most likely safe to bypass the standard diagnostic procedure. After taking care of this problem I have found nothing but a malfunction of the Chevy engine oil push sending unit.

Replacing the Chevy Engine Oil push Sender


*
Chevy Engine Oil press Sensor Location

The ar of the oil press sender stays an worry for most do-it-yourself mechanics. Together you deserve to see indigenous the picture it is a tight fit. They find it in prior of the infection bell housing where it bolts come the motor.I dislike to call you to buy a special device that you"ll just use one time. However, in this instance I"m recommending the you get the special tool designed to remove the press switch. The unique socket has actually an extra thin wall that permits you to get it over the sensor easily. A standard 1 1/16th deep socket doesn"t to the right tight sufficient on the factory installed part. And my 27 mm deep influence socket was as well thick to fit over the sensor. Opportunities are, if you own this car long enough, you could get to use the special device a couple of more times. Repeat failure of the sensor space common and we"ll talk around this in the difficulties section below.

With the said, the very first step is to eliminate the plastic cover end the height of the engine. Surprisingly, also this is a fight. The prior of the cover simply lifts off of 2 retaining posts. However, the earlier of it gets hooked on the behind retaining clips, since it doesn"t have enough clearance above. You"ll have to stick your hand in there and also push down on the behind retainer if lifting increase on the ago side of the engine cover. The next step becomes to disconnect the electric connector. They usage a lock tab to host it in place. You merely pull the white lock tab up and also it will certainly snap come release. Climate you have the right to depress the connector lock and also wiggled it loose from the sensor. As for instead of the sensor that screws in the rear section of the engine block right into an oil gallery. A six-inch expansion attached to a swivel head 3/8 ratchet functions perfectly for removing the Chevy engine oil press sending unit. Here is a three minute video clip that sums increase the replacement procedure rather nicely.

Problems once Replacing the Oil push Sensor


*
Chevy Oil press Sensor screen Filter

The main trouble when instead of the Chevy engine oil pressure sensor is repeat failure. This goes ago to the root reason of the issue. Sludge and debris finds its way inside of the old oil press switch.

This is as soon as Chevy determined to install the filter display for the 2007 model year. Now what wake up is the display screen becomes plugged through junk and also engine oil never reaches the sensor.

Therefore, human being that simply replace the part without replacing the screen find the repairs won"t last lengthy or don"t work-related at all. This likewise leads to man that over there is something else wrong with the automobile.

On older Chevy engines the don"t have the screen repeat failure often originates from lack of engine maintenance. In some cases this is no the error of the present owner, yet the previous one. A lack of engine oil changes can reason sludge deposits to form.

These have the right to break loose and find their way into the input harbor of the replacement pressure sensor. If you have one make certain you change the screen in addition to the switch.

You will need a small pick come fish it out of the oil gallery in the engine block. Once you thread in the sensor that holds the new screen in place. V the low price of the replacement part it doesn"t seem favor a great idea to clean the old screen. In the following section I"ll talk briefly around other worries I"ve discovered when make the efforts to reduced corners top top this repair.

Replacement Chevy Oil pressure Sending Units

Whenever friend have vehicle parts that fail in big numbers the aftermarket measures up to make cheaper solutions. They start mass-producing instead of parts and offering lock at lower prices.

Unfortunately, I have actually seen several concerns with these ultra cheap instead of Chevy engine oil press sensors. I"ve had actually a couple of castle not job-related right out of the box. And also this is not because of the problems mentioned above in the repeat fail section.

With the said, allow me tell you about the worst-case scenario that ns ran into. After replacing the oil pressure sending unit through a part that cost $15, a disaster occurred when I started the engine.

See more: What'S On Your Mind Answers, 50 Questions That Will Free Your Mind

The plastic facility blew the end of the part. Once that happens the oil push gallery becomes open to the atmosphere. The amount of oil that sprays almost everywhere the engine compartment in together a short period of time will certainly amaze you.

The cleanup connected on both the vehicle and also the work area added a couple of more hrs to this disaster. Because that this reason, if a customer wants me to change the Chevy engine oil push sending unit I only use a Delco part. However, ns won"t acquire this component from the dealership, due to the fact that they want practically $100 because that it. And also while I"m ~ above the topic of dealerships, when I priced this procedure I acquired sticker shock. The regional Chevy dealership in my town quoted me a price that parts and also labor that $500 to replace the oil sending out unit. With the quantity of money you can save through doing the yourself, you can afford to obtain a good replacement part, a new screen and the special device that provides it much easier to replace and also still save.