Play terminal Yellow irradiate of Death
By Brett Hartt - iFixItAssmebly Time: 1 hourSkill Level: AdvancedLike a canary in the charcoal mine, a flashing yellow top top the PS3 gaming signals brewing doom. The Yellow irradiate of death (YLOD) is no the latest function playing combat game; it describes the brief warning prior to a complete shutdown of your PS3 – aka Star Trek Warp core overload. Sony officially states that the yellow light might be an concern with one internal component caused by a selection of reasons and should be diagnosed at one of their company centers.There is hope because that this tragic sounding condition. Even if it is it"s the strength supply or the motherboard, her PS3 can frequently be rescued. In the situation of a strength supply failure, simply replace v a new power supply. Overheating is typically the culprit that motherboard failure, especially if has not been retained in a correctly ventilated environment. The result? Cracked or melted solder joints in between the motherboard and processors. Follow these actions to revive her PS3.You are watching: How to fix ps3 yellow light of death
Tools Required:Heat GunThermal pasteThermal padsMulti-bit driver kitSpudger
Step 1: Accessing the clever Plate
To accessibility the smart plate, use the tip of the spudger to remove the black rubber screw cover indigenous the side of the PS3. Then eliminate the solitary 8.5mm T10 protection torx screw from the smart plate.
Pull the smart plate toward the difficult drive bay, climate lift it turn off the body of the PS3. Be sure to store track of the tiny metal clip loosely organized in the optimal cover.
Step 2: Removing height Cover
Step 3: removed the Blu-Ray bowl Drive
Lift the Blu-ray journey from the edge nearest the power supply and also rotate it far from the chassis sufficient to access its ribbon cable. Upper and lower reversal up the retaining flap top top the Blu-ray ribbon cable socket. Be sure you space prying up on the retaining flap, not the socket itself. Traction the ribbon cable the end of the socket and remove the Blu-ray journey from the PS3.
Step 4: Motherboard Assembly
Pull the regulate board ribbon cable straight up and also out the its socket on the motherboard. Then remove the 2 12mm Phillips screws securing the manage board to the lower case and remove the board.
Remove the complying with eight screws securing the motherboard assembly come the lower case: 7 12mm Phillips screws and one 30mm Phillips screw and remove the regulate board bracket.
Use the flat finish of a spudger come pry the tough drive bay cover far from the reduced case and remove the tough drive only cover. Background the motherboard assembly out of the reduced case.
Step 5: AC Inlet
Remove the 7.7mm Phillips screw securing the ground strap come the chassis. Traction the AC-In cables slightly far from the rear cover for clearance to access the AC-In connector. While depressing its locking mechanism, pull the AC-In connector out of the socket ~ above the strength supply.
Step 6: behind Cover
While easy pulling the rear cover far from the logic board assembly, usage the flat finish of a spudger to release the clips along the top and bottom edges of the rear cover and also remove the rear cover native the logic board assembly.
Step 7: warm Sink
Disconnect the pan from the motherboard. Traction the connector straight up and also out the its socket. Remove the 2 9mm Phillips screws securing the storage card reader to the chassis.
Lift the storage card leader out that the PS3 sufficient to accessibility its ribbon cable. Upper and lower reversal up the retaining flap on the storage card leader ribbon cable socket. Be certain you are prying up on the retaining flap, not the socket itself. Pull the ribbon cable the end of the socket and also remove the memory card reader. Disconnect the DC-In cables from the front of the warmth sink. Traction the connector toward the front of the PS3.
Remove the five 9mm Phillips screws securing the power supply to the chassis. Lift the strength supply by its front sheet to clear the two posts attached come the motherboard. Eliminate the strength supply. Remove the four 16.5mm shouldered Phillips screws securing the warm sink come the motherboard. Eliminate the 2 brackets organized under the screws you simply removed.
Step 8: Accessing and Removing Motherboard
Flip up the retaining flap top top the Blu-ray ribbon cable socket. Be sure you room prying up on the retaining flap, not the socket itself. Eliminate the Blu-ray ribbon cable. Upper and lower reversal up the flap on the memory card reader ribbon cable socket and remove the ribbon cable.
Flip up the retaining flap top top the Wi-Fi/Bluetooth ribbon cable socket and also pull the Wi-Fi/Bluetooth ribbon cable out of that is socket. Disconnect the DC-In cable native the motherboard and set it aside. Pull the connector right up and also out of its socket top top the motherboard.
Disconnect the PRAM battery native the motherboard. The PRAM socket is delicate and has the potential come break off the motherboard. If possible, organize down the socket as you disconnect the PRAM battery cable. Turn the PRAM battery slightly counter-clockwise and also remove it from the motherboard assembly.
Remove the blue 8mm Phillips screw securing the hard drive cage come the chassis. First push the difficult drive cage toward the front of the motherboard assembly then eliminate the difficult drive.
Remove the two 3.7mm #0 Phillips screws securing the chassis come the difficult drive socket. Remove the 2 8.3mm #0 Phillips screws securing the 2 halves the the motherboard together.
Carefully feed the Wi-Fi/Bluetooth ribbon cable v the hole in the peak motherboard cover. Remove the height motherboard cover. Remove the motherboard indigenous the bottom motherboard cover.
Step 9: removed Old thermal Pads
Using your fingers or the flat finish of a spudger, eliminate the old thermal pads top top the logic board together indicated: big square heat pads (red boxes in picture), tiny square thermal pads (orange in picture) and small rectangular heat pads (located on the underside of the board, as highlighted in the 2nd picture). Some of the smaller thermal pads may be attached to the steel casing the surrounds the motherboard quite than the motherboard itself.
Set the heat gun come "low" and let it operation for a couple of seconds come reach operating temperature. Stop the motherboard upright, heat up the entire board v the warmth gun. The board must be warm, however not as well hot. This will certainly prevent damages to the board caused by localized thermal expansion. Set the motherboard on a assistance so the the CPU and GPU are totally supported and level. The support should be something that deserve to resist temperature upwards the 300°C. Suggestions: scrap lumber, old books or cardboard box. In the next few steps, you will certainly be reflowing the solder under the chips significant in red. When you start reflowing the chips, execute not touch or relocate the motherboard until it is completely cool. Doing so have the right to render the motherboard irreparably damaged.
Step 10: Reflowing Chips
With the heater gun and also using a one motion, evenly heat (using short heat) each of the four locations for about 25 secs each. Begin heating the GPU, significant "RSX", and also heat the chips in a zigzag order.Ensure the the motherboard has fully cooled before continuing this guide. Use a slim bead that thermal dough on the CPU.
Peel the plastic covers turn off one side of the brand-new thermal pads and also apply the new thermal pads come the motherboard in the places indicated: big square pads (pictured red), small square pads (pictured orange) and tiny rectangular pads (pictured yellow).
See more: Who Is Laertes In The Odyssey, Why Is Laertes Important In The Odyssey
